Active Mobility Regulations 2018 - Singapore Statutes Online

No. S 251

Active Mobility Act 2017

(ACT 3 OF 2017)

Active Mobility Regulations 2018

In exercise of the powers conferred by section 67(1) of the Active Mobility Act 2017, the Land Transport Authority of Singapore, with the approval of the Minister for Transport, makes the following Regulations:

Citation and commencement

1. These Regulations are the Active Mobility Regulations 2018 and come into operation on 1 May 2018.

Definition

2. In these Regulations, unless the context otherwise requires, “hours of darkness” means the time starting 7 p.m. and ending 7 a.m. the following day, both times inclusive.

Markings and signs for public paths

3.—(1) For the purpose of section 2(1) of the Act —

(a)	a pedestrian‑only path sign consists of the symbols set out in diagrams 1 and 2, respectively, of the Schedule;
(b)	an end‑of pedestrian‑only path sign consists of the symbols and words set out in diagrams 3, 4 and 5, respectively, of the Schedule;
(c)	a shared path sign consists of the symbols and words set out in diagrams 6 and 7, respectively, of the Schedule;
(d)	an end‑of shared path sign consists of the words set out in diagram 8 of the Schedule;
(e)	a shared path marking consists of the symbols or words or symbols and words set out in diagrams 9, 10, 11, 12, 13, 14, 15 and 16, respectively, of the Schedule; and
(f)	an end‑of shared path marking consists of the symbols set out in diagrams 17, 18 and 19, respectively, of the Schedule.

(2) A sign or marking as given in a diagram in the Schedule must at least be of the size, and conform to the colour and type, as shown in the diagram set out in the Schedule.

(3) The dimension of a sign or marking as given in a diagram in the Schedule denotes the dimension in millimetres unless otherwise stated.

(4) The direction of any arrow or other indication on a sign or marking shown in the diagrams in the Schedule may be reversed or otherwise varied as circumstances may require.

(5) The fact that a sign or marking differs in size, colour, form or font from that shown in the relevant diagram in the Schedule does not prevent the sign or marking from being a pedestrian‑only path sign, an end‑of pedestrian‑only path sign, a shared path sign, an end‑of shared path sign, a shared path marking or an end‑of shared path marking, as the case may be, so long as the difference —

(a)	is slight;
(b)	is not calculated to mislead; and
(c)	does not affect the substance of the message in the sign or marking.

Non-compliant bicycle

3A.—(1) For the purposes of the definition of “non-compliant bicycle” in section 2(1) of the Act, a bicycle is a non-compliant bicycle if it does not comply with any of the following requirements which are prescribed for all bicycles generally:

(a)	the unladen weight of the bicycle does not exceed 20 kilograms;
(b)	the width of the bicycle does not exceed 700 millimetres.

(2) In this regulation —

“unladen weight”, for a bicycle, means the weight of the bicycle, including the body and all equipment and accessories (if any) attached to the bicycle, but excluding any person or carry-on baggage on the bicycle;

“width”, for a bicycle, means the width of the bicycle, including the body and all equipment and accessories (if any) attached to the bicycle, but excluding any person or carry-on baggage on the bicycle.

[S 909/2018 wef 02/01/2019]

Non-compliant PAB

3B.—(1) For the purposes of the definition of “non-compliant power-assisted bicycle” in section 2(1) of the Act, a 2015 power-assisted bicycle is a non-compliant power-assisted bicycle if it does not comply with any of the following requirements which are prescribed for all 2015 power-assisted bicycles generally:

(a)

the unladen weight of the PAB does not exceed 20 kilograms;

(b)

the width of the PAB does not exceed 700 millimetres;

(c)

the aggregate maximum power output rating of the electric motor of the PAB does not exceed 200 watts;

(d)

the maximum speed of the PAB does not exceed 25 km/h when solely propelled by its electric motor;

(e)

the electric motor of the PAB is designed so as —

(i)	to stop providing further power assistance when the PAB attains a speed of 25 km/h or more; and
(ii)	to reduce and stop providing power assistance when the rider of the PAB stops pedalling;

(f)

the PAB is affixed with a registration number plate that conforms to the requirements in rule 11(2) of the Road Traffic (Registration of Power-Assisted Bicycles) Rules 2017 (G.N. No. S 451/2017).

(2) For the purposes of the definition of “non-compliant power-assisted bicycle” in section 2(1) of the Act, a 2016 power-assisted bicycle is a non-compliant power-assisted bicycle if it does not comply with any of the following requirements which are prescribed for all 2016 power-assisted bicycles generally:

(a)

the unladen weight of the PAB does not exceed 20 kilograms;

(b)

the width of the PAB does not exceed 700 millimetres;

(c)

insofar as the power of the electric motor of the PAB is concerned —

(i)	the aggregate maximum power output rating of the electric motor does not exceed 200 watts; or
(ii)	where the aggregate maximum power output rating of the electric motor exceeds 200 watts, the maximum continuous rated power of the electric motor does not exceed 250 watts;

(d)

the maximum speed of the PAB does not exceed 25 km/h when solely propelled by its electric motor if the aggregate maximum power output rating of its electric motor does not exceed 200 watts;

(e)

the electric motor of the PAB is designed so as —

(i)	to stop providing further power assistance when the PAB attains a speed of 25 km/h or more; and
(ii)	to reduce and stop providing power assistance when the rider of the PAB stops pedalling;

(f)

the PAB conforms to the standard EN 15194 if its electric motor satisfies sub-paragraph (c)(ii);

(g)

for a PAB which conforms to the standard EN 15194, the electric motor of the PAB is also designed so as to progressively reduce power assistance as the speed of the PAB approaches —

(i)	the speed of 25 km/h; or
(ii)	the speed at which its electric motor stops providing power assistance,

whichever is lower;

(h)

the PAB is affixed with a registration number plate that conforms to the requirements in rule 11(2) of the Road Traffic (Registration of Power-Assisted Bicycles) Rules 2017;

(i)

for a PAB which conforms to the standard EN 15194, the PAB is legibly and permanently marked with the following information:

(i)

a successive frame number;

(ii)

the name of the manufacturer of the PAB or the manufacturer’s representative;

(iii)

the words “EN 14764” and “EPAC”;

(iv)

the words “According to EN 15194:” which are followed by words that specify the following:

(A)	the speed, in km/h, at which the PAB’s electric motor stops providing power assistance;
(B)	the maximum continuous rated power, in watts, of the PAB’s electric motor.

(3) For the purposes of the definition of “non-compliant power-assisted bicycle” in section 2(1) of the Act, any other power-assisted bicycle which is neither a 2015 power-assisted bicycle nor a 2016 power-assisted bicycle is a non-compliant power-assisted bicycle if it does not comply with any of the following requirements which are prescribed for all these other power-assisted bicycles generally:

(a)

the unladen weight of the PAB does not exceed 20 kilograms;

(b)

the width of the PAB does not exceed 700 millimetres;

(c)

the maximum continuous rated power of the electric motor of the PAB does not exceed 250 watts;

(d)

the maximum speed of the PAB does not exceed 25 km/h when solely propelled by its electric motor;

(e)

the electric motor of the PAB is designed so as —

(i)	to stop providing further power assistance when the PAB attains a speed of 25 km/h or more;
(ii)	to reduce and stop providing power assistance when the rider of the PAB stops pedalling; and
(iii)	to progressively reduce power assistance as the speed of the PAB approaches the speed of 25 km/h or the speed at which the PAB’s electric motor stops providing power assistance, whichever is lower;

(f)

the PAB is affixed with a registration number plate that conforms to the requirements in rule 11(2) of the Road Traffic (Registration of Power-Assisted Bicycles) Rules 2017;

(g)

the PAB conforms to the standard EN 15194;

(h)

the PAB is legibly and permanently marked with the following information:

(i)

a successive frame number;

(ii)

the name of the manufacturer of the PAB or the manufacturer’s representative;

(iii)

the words “EN 14764” and “EPAC”;

(iv)

the words “According to EN 15194:” which are followed by words that specify the following:

(A)	the speed, in km/h, at which the PAB’s electric motor stops providing power assistance;
(B)	the maximum continuous rated power, in watts, of the PAB’s electric motor.

(4) In this regulation —

“2015 power-assisted bicycle” means a PAB that is approved and sealed before 1 December 2015 by an authorised examiner under the Road Traffic (Power-Assisted Bicycles — Approval) Rules 2004 (G.N. No. S 768/2004);

“2016 power-assisted bicycle” means a PAB that is approved and sealed between 1 December 2015 and 31 January 2016 (both dates inclusive) by an authorised examiner under the Road Traffic (Power-Assisted Bicycles — Approval) Rules 2004;

“EN 15194” means the European Standard EN 15194:2009+A1:2011 titled “Cycles — Electrically power assisted cycles — EPAC Bicycles” approved by the European Committee for Standardization on 22 November 2008 (except clause 4.2.4.3 in EN 15194:2009+A1:2011) and as amended by Amendment 1 approved by that European Committee for Standardization on 8 October 2011;

“unladen weight”, for a power-assisted bicycle, means the weight of the bicycle, including the body and all equipment and accessories (if any) attached to the bicycle, but excluding any person or carry-on baggage on the bicycle;

“width”, for a power-assisted bicycle, means the width of the bicycle, including the body and all equipment and accessories (if any) attached to the bicycle, but excluding any person or carry-on baggage on the bicycle.

[S 909/2018 wef 02/01/2019]

Non-compliant personal mobility device

4.—(1) For the purposes of the definition of “non‑compliant personal mobility device” in section 2(1) of the Act, a personal mobility device is a non‑compliant personal mobility device if it does not comply with any of the following requirements which are prescribed for all personal mobility devices generally:

(a)	the maximum speed of the personal mobility device does not exceed 25 kilometres per hour under all circumstances;
(b)	the unladen weight of the personal mobility device does not exceed 20 kilograms;
(c)	the width of the personal mobility device does not exceed 700 millimetres.

(2) In this regulation —

“unladen weight”, for a personal mobility device, means the weight of the personal mobility device, including the body and all equipment and accessories (if any) attached to the device, but excluding any person or carry‑on baggage on the device;

“width”, for a personal mobility device, means the width of the personal mobility device, including the body and all equipment and accessories (if any) attached to the device, but excluding any person or carry‑on baggage on the device.

Speed limit for footpaths

5. For the purpose of section 21(1) of the Act, the maximum speed for a footpath is 15 kilometres per hour.

Speed limit for shared paths

6. For the purpose of section 21(1) of the Act, the maximum speed for a shared path is 25 kilometres per hour.

Speed limit for mechanised sweeper

7. For the purpose of paragraph (b) of the definition of “mechanised sweeper” in section 2(1) of the Act, the maximum speed is 40 kilometres per hour.

Restriction on number of passengers carried

8.—(1) A rider of a bicycle on a footpath or shared path must not ride with more passengers on the bicycle than the bicycle is designed to carry.

(2) A rider of a PAB on a shared path must not ride with more passengers on the PAB than the PAB is designed to carry.

Passenger on bicycle and PAB

9.—(1) A rider of a bicycle on a footpath or shared path must not ride with a passenger on the bicycle unless —

(a)	where the passenger is a child below 12 years of age, the child is in a properly constructed seat or carrier that is designed for carrying such a child and is affixed to the bicycle; and
(b)	in all other cases, the passenger is in a seat designed for such a passenger.

(2) Subject to regulation 10(2), a rider of a PAB on a shared path must not ride with a passenger on the PAB unless the passenger is in a seat designed for such a passenger.

Age restriction on use of PAB

10.—(1) An individual below 16 years of age —

(a)	must not ride a PAB on a shared path; and
(b)	must not be carried as a passenger on a PAB which is ridden on a shared path.

(2) A rider of a PAB on a shared path must not ride with a passenger who is below 16 years of age.

Load restriction on bicycle and PAB

11. A rider of a bicycle on a footpath or shared path, or a PAB on a shared path —

(a)	must ensure that every load carried on the bicycle or PAB, as the case may be, is properly and rigidly secured to the bicycle or PAB; and
(b)	must not carry on the bicycle or PAB, as the case may be, a load which is of such dimensions as to cause or be likely to cause danger, obstruction or annoyance to other individuals using the footpath or shared path, as the case may be.

Lights on bicycle and PAB

12. A rider must not ride, during hours of darkness, a bicycle on a footpath or shared path, or a PAB on a shared path, unless the bicycle or PAB —

(a)

displays a white light that is clearly visible for a reasonable distance from the front of the bicycle or PAB; and

(b)

displays either —

(i)	a red light that is clearly visible for a reasonable distance from the back of the bicycle or PAB; or
(ii)	a red reflector that is clearly visible for a reasonable distance from the back of the bicycle or PAB when light is projected onto the reflector.

Lights on personal mobility device or rider

13. A rider must not ride, during hours of darkness, a personal mobility device on a footpath or shared path unless the rider wears or the personal mobility device displays —

(a)	a white light that is clearly visible for a reasonable distance from the front of the rider or device, as the case may be; and
(b)	a red light that is clearly visible for a reasonable distance from the back of the rider or device, as the case may be.

Penalty

14. Any person who contravenes regulation 8(1) or (2), 9(1) or (2), 10(1) or (2), 11, 12 or 13 shall be guilty of an offence and shall be liable on conviction —

(a)	in the case of a first offence, to a fine not exceeding $1,000 or to imprisonment for a term not exceeding 3 months or to both; and
(b)	in the case of a second or subsequent offence, to a fine not exceeding $2,000 or to imprisonment for a term not exceeding 6 months or to both.

Made on 30 April 2018.

CHAN HENG LOON ALAN

Chairman,
Land Transport Authority of Singapore.

[LTA/LEGL/L18.056.002/JAS/DT/REG.18.01; AG/LEGIS/SL/2C/2015/4 Vol. 1]

(To be presented to Parliament under section 67(4) of the Active Mobility Act 2017).

Search within Legislation